Difference between revisions of "EN/documentation/ooo3 user guides/getting started/getting started with macros"
m (1 revision) |
|||
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | {{DISPLAYTITLE:Getting Started with Macros}} | + | <section begin=title /><noinclude>{{DISPLAYTITLE:</noinclude>Chapter 13. Getting Started with Macros<noinclude>}}</noinclude><section end=title /> |
| + | |||
{{Documentation/GS3MacroTOC | {{Documentation/GS3MacroTOC | ||
|ShowPrevNext=block | |ShowPrevNext=block | ||
| − | |PrevPage= | + | |PrevPage=EN/documentation/ooo3_user_guides/getting_started/saving_draw_documents_as_web_pages |
| − | |NextPage= | + | |NextPage=EN/documentation/ooo3_user_guides/getting_started/creating_a_simple_macro |
}} | }} | ||
| − | This is Chapter '''13''' of '''Getting Started with OpenOffice.org 3.x''', produced by the [http://oooauthors.org/ OOoAuthors group]. A PDF of this chapter is available from | + | This is Chapter '''13''' of '''Getting Started with OpenOffice.org 3.x''', produced by the [http://oooauthors.org/ OOoAuthors group]. A PDF of this chapter is available from {{SecTitle|EN/documentation/ooo3_user_guides/chapters}}. |
| Line 13: | Line 14: | ||
OpenOffice.org macros are usually written in a language called StarBasic, or just abbreviated Basic. Although you can learn Basic and write macros, there is a steep learning curve to writing macros from scratch. The usual method for a beginner is to use the built-in macro recorder, which records your keystrokes and saves them for use. | OpenOffice.org macros are usually written in a language called StarBasic, or just abbreviated Basic. Although you can learn Basic and write macros, there is a steep learning curve to writing macros from scratch. The usual method for a beginner is to use the built-in macro recorder, which records your keystrokes and saves them for use. | ||
| − | Most tasks in OpenOffice.org are accomplished by “dispatching a command" (sending a command), which is intercepted and used. The macro recorder works by recording the commands that are dispatched (see | + | Most tasks in OpenOffice.org are accomplished by “dispatching a command" (sending a command), which is intercepted and used. The macro recorder works by recording the commands that are dispatched (see {{SecTitle|EN/documentation/ooo3_user_guides/getting_started/sometimes_the_macro_recorder_fails}}/The dispatch framework). |
| − | |||
{{CCBY}} | {{CCBY}} | ||
[[Category:Getting Started (Documentation)]] | [[Category:Getting Started (Documentation)]] | ||
Latest revision as of 11:00, 9 April 2012
This is Chapter 13 of Getting Started with OpenOffice.org 3.x, produced by the OOoAuthors group. A PDF of this chapter is available from [[EN/documentation/ooo3_user_guides/chapters|EN/documentation/ooo3 user guides/chapters]].
Your first macro
A macro is a saved sequence of commands or keystrokes that are stored for later use. An example of a simple macro is one that “types" your address. The OpenOffice.org macro language is very flexible, allowing automation of both simple and complex tasks. Macros are especially useful to repeat a task the same way over and over again.
OpenOffice.org macros are usually written in a language called StarBasic, or just abbreviated Basic. Although you can learn Basic and write macros, there is a steep learning curve to writing macros from scratch. The usual method for a beginner is to use the built-in macro recorder, which records your keystrokes and saves them for use.
Most tasks in OpenOffice.org are accomplished by “dispatching a command" (sending a command), which is intercepted and used. The macro recorder works by recording the commands that are dispatched (see Sometimes the macro recorder fails/The dispatch framework).
| Content on this page is licensed under the Creative Common Attribution 3.0 license (CC-BY). |
